Although all door handles might look the same, only one kind would fit into a Chevrolet C1500. The rivet makes sure it stays put. Push the window regulator handle back into place and secure it with the retaining clip, then secure the trim panel with the screws that you removed. Step 5:From there, pull the rod out of the latch. Since 1918, Dorman Products has supplied the automotive aftermarket with high-quality replacement parts, hardware and fasteners.
Friends with this model have had the same problems. It may be easier to reconnect linkages by removing the metal panel also. Take the trim off the top interior of the door by prying it carefully with a screwdriver. However, there are a few things to remember when painting car door handles. Find the screws that are holding the exterior door handle onto the door from the inside. The best one I have found is sold on eBay for 12 dollars. Replace the door panel, door handle cup, armrest and triangular trim in the reverse order of removal.
Tighten the bolts with a small adjustable wrench. Plug in the speaker - pass the wire under the divider before connecting it. You will need to get inside the door replace the latch. Reattach the 2 control rods - they will just snap into place. Alternatively you could use a small bolt and nut.
It will stop cold air from entering. Maybe you could borrow one from Auto Zone, or have a local body shop install the rivet. That is why it is important to take note of the door handle part number when searching for a replacement part. Since the Chevy S10 is a discontinued model of truck, getting replacement parts like a door latch could be tricky. Remove the door handle from the outside of the door. Use care here, plastic gets brittle over the years. You will have to drill out a rivet to remove the old assembly, but it can be replaced with a simple machine screw when re-installing the new handle assembly.
Since finding a new door handle that fits could be next to impossible for phased-out or discontinued car models, looking through used door handles could be the only option. Step 6:Use a ¼-inch drive socket to remove the two nuts on the door then pull the handle out as carefully as possible. Pull the handles straight off. Step 2:Remove any screws on the outside of the door panel too. Test the handle to see if it works before finishing up the job. The fork is another specialized tool. You'll have to bend the prong a bit with your finger to line it up.
They are fit specifically for the makes and models that they are designed for--it's a guaranteed fit for the car every time. There are many posts on these door handles breaking, it is a common problem. Yes, it's winter - today it was above freezing so I decided to do the job. Remove all mounting screws for the trim panel with a screwdriver. Dorman Door Handle Made from carefully treated and coated plastics, Dorman door handles are designed not to bend and warp no matter what the weather conditions they have to face.
Apr 11, 2009 You should replace the handle with an aluminum version. Squeeze the small speaker connector to release it. For more information go to. I've replaced 2 in the last 4 years. The big rivet gun is from my days doing collision repair. Clip the trim cover back over the door armrest section of the Chevrolet Prizm, and then secure the trim over the top of the door panel and reattach the door armrest with the screws.
However, this is not the case for Chevrolet C1500 door handles. I removed the plastic sheet from the old handle and reused it. You will have to drill out a rivet to remove the old assembly, but it can be replaced with a simple machine screw when re-installing the new handle assembly. Pry out the power controls if equipped with a trim stick and disconnect the electrical connector. Pry up on the lower side of the door panel with a panel removal tool to release the retaining clips. Peel away the plastic water shield covering the door. Lift the door panel up and away from the door, being careful to slide the door-lock and window switch wiring harnesses through the holes in the panel before pulling the door panel.
Step 3:Unscrew the handle from the door, remove it, then set the new car door into place. Once you have one released the rest are easier. The assembly fits into the door very tightly with some teeth that you will see on the back of the replacment unit, which will also help you see how the old once will need to slide in order to be removed one the rivet is drilled out. Remove the interior door handle and window crank by loosening the set screws at the base of the handles with the screwdriver. Do everything in reverse order. I had to re-glue it Now we can get at the handle. These door handles, however, do not have provision for door locks.
Peel away the paper backing on the door to reveal the backside of the door handle. I bought the replacement handle assembly from the local Advance Auto Parts store. Step 3:Lift the panel up in order to release these hooks. Insert the replacement door handle into the door and apply the mounting nuts or bolts. Lift the panel straight up then away from the door. And even after that, quality and longevity of the door handle cannot be guaranteed, especially if the used auto part has been exposed to the elements for a long time. If you do not have a door trim pin removal tool, you can use a sturdy putty knife to pry the panel away where the pins seat into the door, but take care not to damage the door panel.